When we finished our basement, I had the electrician run two Cat-6 cables to a box right by every outlet and back to a single point. I had to terminate and punch everything down. But, now I have Ethernet throughout the basement.
Totally worth it.I just recently ran a bunch of cables in the house. Lots of work, but yes definitely worth it.
I have a bunch of useless phone jacks in several rooms of my house, and I’m wondering how much this would cost me. I took a look at the housing behind them and it doesn’t seem like anything I could convert myself, so it seems like a qualified electrician job…
You can just cut them out and replace them with Ethernet wall jacks, they are pretty cheap. Most have color coded punch downs on the back. Use the existing phone lines to pull the cables through the walls to wherever the phone lines end in a junction and that’s where you can set up a switch or router.
If your house was built after 2000 (or has updated wiring) you might wanna look into Ethernet over power. The kits are usually less than 50 bucks (depending on the speeds you’re using) and they allow you to hardline your computer without running a cable across the entire house.
The way they work is by plugging a parent box directly into the wall near your router you can run a short Ethernet to the box and then plug in the sister box near your gaming rig and run another short Ethernet from the wall to your computer. It basically just uses the copper wires of the house wiring to transfer the data.
There are some exceptions to be aware of. If you have a particularly large house the speeds might suffer over a long enough run. Or if they have the internet on an entirely different breaker panel it won’t work.
I am currently using one at my house. The wire gives me better ping, but slightly lower total download speed. So if I’m downloading a big game or something I’ll just unplug the Ethernet at let it download faster over wifi and then I switch back to wired for gaming.
I wish there was a way to test this without spending 50 bucks. My results have simply been that the resulting signal is just as unreliable as WiFi.
I used one in an apartment where I had my modem in the living room, then went out to power, power back to an access point in my room that had my work VPN built into it. Ran a VoIP phone off of of it and 2 work desktops. Worked in IT at the time so I was using multiple remote softwares and didn’t have any issues.
Maybe just order one for pickup at a local store and return it if you aren’t satisfied.
I did in my house which was built in the 1950s or 60s and it works. With that said, it was only ok and I wouldn’t use this for anything but internet access and some light streaming. This was 10 years ago so it is possible they have gotten better. I have since moved to mesh wifi and it literally solved every issue I had and the whole house has incredible wifi no matter where you are. Plus I use the AP’s to plug in my more dedicated stuff since it’s faster than wifi to use the backhaul the APs use to communicate with. I do wish I could afford to redo my house and put in ethernet wiring everywhere and have a dedicated switch for everything.
I needed to get internet to a building that’s around 400 feet away. I had the opportunity to get a trench dug, so I took a gamble, laid a conduit and ran shielded CAT6. I say gamble because that’s over the rated limited of CAT cable, but I figured it was going to be easier then trying to get a reliable wiki bridge running. The home network itself has been solid since.
Going over 300 just limits you on speed after errors
I thought it was more to do with packet loss.
Packet loss is primarily a CRC thing. You might get 99% of a packet, but it fails the error check so it’s dropped and re-requested.
Just pop your ancient phone line/ cable outlet off the wall and fish a couple wires up/down the wall
I had one room in my old house where the line wasnt stapled to the framing and was able to bind them together and pull it through at the other end. the rest were stapled
current house I can run them through the attic and down the inside of the walls but the attic is full of rat shit and I can’t motivate myself even with hazmat suit.
Paid an electrician to fish ethernet for me from my utility closet where the router is to my home office. Was well worth the expense. WiFi is great, and I use it for all the other devices in the house. But I work from home most days, and I got tired of the random slow-downs and drops.
Yep. If I have the ability to run a cable I do.
Better make WiFi routers hubs between every 20ft and interconnect them as mesh network this way your setup will be many times more robust, speaking from experience, on the job we have internet cables drawn inside walls so they aren’t accessible and some cables can lose some signal strength after a few years of usage, these hubs are mainly for strengthening signal at key points, but also if at some point signal is lost then WiFi bridges can act as temporary solution until you find where is that cable in chain of cables and replace it
This will have literally a hundred times the latency and terrible jitter.
Still better than open half a building of walls
