I got answers here but you’ll need to do a little leg work.
First off, get a good guess at what the marker is. If it’s permanent ink, it’s probably using alcohol base, if it’s acrylic it’s water, etc. Depending on the solvent used in the marker you can pick a coating material that won’t damage the original markings. You’re going to want it in spray can form unless you own an airbrush.
If all else fails, someone else pointed out automotive clear coat. That will do fine if you follow the info carefully.
Once you have a clear coat that either does or preferably doesn’t react with the mark, you’re going to tape off your phone. Masking tape is fine, I find washi tape from the scap booking section to work better. It sticks tighter but peals back up easily and without residues. Go around the camera hump, over the surface, around the outside, and completely cover the screen. Always do more than you think is necessary, because it’s easier to waste tape than remove paint.
Now for the best results you’re going to want a hot, dry, windless environment. If it’s not like that outside you can do it indors with ventilation, just lay down and old sheet and open some windows.
Now your clear coat is going to be in a spray can. Look around the tip for a mark on the can, that will indicate the angle of the intake. Point the sprayer the same direction and test it a few times on cardboard until you have a good and steady stream. Practice the next part if you have any doubts about yourself. Just cut a piece of cardboard that’s phone sized and pretend you’re doing the real thing.
You’re going to start each spray off to the side of the target. The initial push and your ability to move is not perfect even after years of doing this and will lead to a wet spot. Make sure that spot is on the work area and not the piece. Steadily move across the piece and end the spray on the work area again, this prevents splatter.
You’re going to gently dust the phone in coat. Adjust to the next pass and do it again. Then let this coat dry completely not tacky, not dull, full dry.
Turn the phone 90 degrees and do it again. You’re going to repeat this process 30 or 40 times. Eventually it will build up into one solid coating across the entire surface. Ideally you let that cure for 24 hour.
This is your phone so I understand if that’s not doable, just make sure to ler each coat dry.
remotelove@lemmy.ca
I got answers here but you’ll need to do a little leg work.
First off, get a good guess at what the marker is. If it’s permanent ink, it’s probably using alcohol base, if it’s acrylic it’s water, etc. Depending on the solvent used in the marker you can pick a coating material that won’t damage the original markings. You’re going to want it in spray can form unless you own an airbrush.
If all else fails, someone else pointed out automotive clear coat. That will do fine if you follow the info carefully.
Once you have a clear coat that either does or preferably doesn’t react with the mark, you’re going to tape off your phone. Masking tape is fine, I find washi tape from the scap booking section to work better. It sticks tighter but peals back up easily and without residues. Go around the camera hump, over the surface, around the outside, and completely cover the screen. Always do more than you think is necessary, because it’s easier to waste tape than remove paint.
Now for the best results you’re going to want a hot, dry, windless environment. If it’s not like that outside you can do it indors with ventilation, just lay down and old sheet and open some windows.
Now your clear coat is going to be in a spray can. Look around the tip for a mark on the can, that will indicate the angle of the intake. Point the sprayer the same direction and test it a few times on cardboard until you have a good and steady stream. Practice the next part if you have any doubts about yourself. Just cut a piece of cardboard that’s phone sized and pretend you’re doing the real thing.
You’re going to start each spray off to the side of the target. The initial push and your ability to move is not perfect even after years of doing this and will lead to a wet spot. Make sure that spot is on the work area and not the piece. Steadily move across the piece and end the spray on the work area again, this prevents splatter.
You’re going to gently dust the phone in coat. Adjust to the next pass and do it again. Then let this coat dry completely not tacky, not dull, full dry.
Turn the phone 90 degrees and do it again. You’re going to repeat this process 30 or 40 times. Eventually it will build up into one solid coating across the entire surface. Ideally you let that cure for 24 hour.
This is your phone so I understand if that’s not doable, just make sure to ler each coat dry.